Eicon Networks S52 Guía de usuario Pagina 83
- Pagina / 91
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Eicon Connections for Linux User’s Guide
page 81
APPENDIX D
X.3 PAD Parameters
X.3 PAD parameters set the guidelines for how the PAD deals with different terminal
emulations. You use X.3 PAD parameters to control such features as local echo and line feed
insertions after carriage returns, to enable local editing, and to determine what service signals
are forwarded to the user.
X.3 PAD Parameter Support
There are 22 standard X.3 PAD parameters that are recognized internationally. These
parameters and the functions they control are described later in this section. There also exist
national X.3 PAD parameters numbered higher than 22, but their definition varies from country
to country. The Eiconcard Host PAD and Eiconcard Terminal PAD do not support these national
parameters.
You should be aware that each of the 22 international X.3 PAD parameters has both mandatory
and optional values. The Eiconcard Host PAD and Eiconcard Terminal PAD support all
mandatory values (as defined in CCITT Recommendation X.3, 1984); they also support many
of the optional parameter values. Network support, however, will vary. Consult your network
manager for specifics.
How to Set X.3 PAD Parameters
There are several ways to set X.3 PAD parameters. You can set them using tpadcfg or
tpadprof with the Eiconcard Terminal PAD, or using the Linux stty command with the
Eiconcard Host PAD.
The initial values for the Eiconcard Terminal PAD are setup using either tpadcfg or tpadprof.
The Eiconcard Host PAD initial values are set in the device configuration entry in the
/etc/gettydefs file.
X.3 PAD Parameters
The table below shows the CCITT PAD Parameters.
Number Description
1 PAD recall using a character
2 Echo
3 Selection of data forwarding
character
4 Selection of idle timer delay
5 Ancillary device control
6 Control of PAD service signals
7 Operation on receipt of break signal
8 Discard output
9 Padding after carriage return
- User’s Guide 1
- page 4 4
- Contents 5
- About this Guide 7
- Typographic Conventions 8
- CHAPTER 2 9
- Eiconcard Services 10
- Eiconcard Host PAD Driver 11
- Eiconcard Terminal PAD Driver 11
- Eiconcard Routing Services 12
- Eiconcard SNMP Services 13
- Integrating with OSI 13
- OSI Model 14
- For More Information 15
- page 14 16
- CHAPTER 3 17
- Completing the Installation 18
- Removing Eiconcard Router 18
- Removing Eiconcard Services 19
- Introduction 19
- Install an Eiconcard 19
- Uninstall an Eiconcard 20
- Configure Eiconcard Protocol 20
- High-Level Services 21
- Line Protocols 21
- Dialer Selection 21
- Changing Protocol Parameters 22
- Eiconcard Memory Requirements 22
- Online Help 23
- Configuration Procedure 24
- Configure Advanced Options 25
- Configure the PAD 25
- page 24 26
- Terminal PAD 27
- page 26 28
- Using tpad with cu and uucp 29
- The cu Commands 30
- page 30 32
- X.3 PAD Parameters 33
- The uucp Configuration Files 33
- Using uucp and cu 34
- page 34 36
- CHAPTER 5 37
- page 36 38
- Load the mpr.if file 40
- IP Routing Tables 40
- Displaying IP-routing Entries 42
- Testing Your Installation 42
- The Test System 43
- Resources for the Test System 43
- The Addressing Scheme 43
- Configuring the Eiconcards 44
- Creating an X.25 Test Circuit 45
- Troubleshooting 46
- Setting Up a PPP Connection 48
- page 48 50
- page 50 52
- page 52 54
- CHAPTER 6 55
- Load/Self-test Timeout Period 56
- Watchdog Wake Up Period 56
- X.25 socket driver 56
- Modem and Null-Modem Cables 57
- Establishing Contact 58
- Modem Cables 59
- HSI/V.24 Converter 60
- Null-Modem Cables 61
- X.21 HSI Null-Modem Cable 62
- References 63
- Facility Types 64
- Facility Syntax 64
- Examples of User Facilities 64
- Packet size 65
- Window Size 65
- Fast Select 66
- Throughput Class Negotiation 66
- Bilateral CUG Selection 68
- Reverse Charging 68
- Priority Traffic: 0,0,1,1 69
- Traffic: 69
- 1,1,0,0,1,1 69
- Networks and DNICs 70
- X.25 Diagnostic Codes 71
- page 70 72
- X.25 Cause Codes 73
- ASCII Control Codes 74
- page 74 76
- X.29 Call User Data Format 77
- page 76 78
- Key Packet Formats 79
- Call Accepted Packet Format 80
- Clear Request Packet Format 81
- 2:n Echo 85
- 5:n Auxiliary Device Control 85
- page 84 86
- 8:n Discard data 87
- 9:n Carriage return padding 87
- 10:n Line folding 87
- 11:n Communication speed 87
- 15:n Editing 88
- 14:n Linefeed padding 88
- 16:n Character delete 89
- 17:n Line delete 89
- 18:n Line redisplay 89
- 19:n Editing service signals 89
- 20:n Echo mask 90
- 21:n Parity treatment 90
- 22:n Page wait 90
Relacionado con productos y manuales para Redes Eicon Networks S52
Redes Eicon Networks Diva 2440 Manual de usuario
(83 paginas)
(83 paginas)
Redes Eicon Networks Eicon 1550 Manual de usuario
(10 paginas)
(10 paginas)
Redes Eicon Networks C20 Manual de instrucciones
(410 paginas)
(410 paginas)
Redes Eicon Networks C20 Especificaciones
(24 paginas)
(24 paginas)
Redes Eicon Networks DIVA T/A ISDN Modem Guía de usuario
(122 paginas)
(122 paginas)
Redes Eicon Networks Diva 2430 Guía de usuario
(68 paginas)
(68 paginas)
Redes Eicon Networks DIVA T/A ISDN Modem Guía de usuario
(191 paginas)
(191 paginas)
Redes Eicon Networks Eicon 1550 Especificaciones
(8 paginas)
(8 paginas)
Redes Eicon Networks 800-241 Guía de usuario
(52 paginas)
(52 paginas)
Redes Eicon Networks 1530 Guía de usuario
(162 paginas)
(162 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales