Eicon Networks V8.3 Especificaciones Pagina 1

www.eicon.comEiconcard S5x Familyfor ISA-Compatible Bus

10 Connecting to a Third Party NT1Connecting to a Third Party NT1To connect to a third party NT1, you must use the ISDN S/T Cable. This cable includes

Termination 11TerminationThis section applies to S/T interface users in Australia and North America, and provides instructions to help set up terminat

12 TerminationMultiple ISDN DevicesIf the NT1 is connected to more than one ISDN device, follow the procedures below.75 meters or moreIf the connectio

Making an HSI Connection 13Making an HSI ConnectionThe Eiconcard S5x can connect as a DTE to devices such as Data Service Units (DSUs) which support o

14 Interface SpecificationsInterface SpecificationsThe standards compliant with the interfaces supported on the HSI port are listed in Table 2. The re

Cable Construction Information 15Cable Construction InformationIf you plan to construct your own HSI cables, be sure to observe the guidelines given b

16 The V.24 InterfaceThe V.24 InterfaceA pin-out diagram for the V.24 DCE interface is shown in Figure 5. The signal definitions and names are listed

The V.35 Interface 17Table 5. V.35 Interface SignalsPin # Signal Name Direction CCITT #1 PGND Protective Ground Common 1014 RTS Request to Send Output

18 The X.21 InterfaceThe X.21 InterfaceA pin-out diagram for the X.21 interface is shown in Figure 7. The signal definitions and names are listed in T

Null-Modem Cables 19Null-Modem CablesThe wiring diagrams below shows the connections required to construct a back-to-back HSI—HSI cable, and V.35 - AS

www.eicon.comFourth Edition (July 2001) 203-078-04Eicon, Eiconcard, and the Eicon logo are either trademarks or registered trademarks of Eicon Network

20 Null-Modem CablesFigure 9. HSI X.21 Null-Modem Cable (300-032)Figure 10. HSI V.35 Null-Modem Cable for AS/400 (300-047)24202619161312117HSIHSI16131

Null-Modem Cables 21Figure 11. HSI Null-Modem Conversion Cable (300-033)1123149865432HSIHSI261913165472083TWISTED PAIRS(MANDATORY)DRAIN WIREBRAID11162

22 AppendixAppendixSetting the I/O AddressThe Eiconcard S5x is shipped with the I/O address set to 380h. This setting only needs to be changed if anot

Setting the I/O Address 23Setting I/O Addresses when Installing Multiple EiconcardsIf you are installing two or more Eiconcards in the PC, for every E

24 Selecting an InterfaceSelecting an InterfaceThe Eiconcard S5x is capable of connecting as a DTE to devices which support the V.24, V.35, or X.21 in

Software Configuration 25Software ConfigurationUse the information below to assign the card’s interrupt request level and memory segment address.Inter

26 LED FunctionalityLED FunctionalityEiconcard S50, S52Note The Eiconcard S50 has only one HSI port.Configuration StatusThis status light illuminates

LED Functionality 27Eiconcard S51The Eiconcard S51 has three status lights (LEDs) on the end bracket. Two of these lights indicate the status of the I

28 Technical SpecificationsTechnical SpecificationsTechnical Data• IBM PC, PC AT, and PS/2 Model 30 bus compatibleHardware Installation• Interrupt lev

International Regulatory Information 29International Regulatory InformationRegulatory Information for the USA:WARNING. Changes or modifications to thi

www.eicon.comTable of ContentsIntroduction ... 5Installing the Eiconcard S5x...

30 Regulatory Information for the USA:FCC Part 68 NoticeThis unit complies with Part 68 of the FCC rules. On the bottom of this equipment is a label t

Regulatory Information for Canada 31Regulatory Information for CanadaNOTICE: The Industry Canada label identifies certified equipment. This certificat

32 Regulatory Information for EuropeRegulatory Information for Europe EU Declaration of ConformityEN: Eicon Networks Corporation declares that this eq

Regulatory Information for Europe 33Safety Status: SELVNo voltages within this equipment exceed SELV voltages. All interconnection points and ports ar

34 Regulatory information for AustraliaRegulatory information for Australia• This customer equipment shall only be installed in a PC that requires the

203-078-04

www.eicon.com

Introduction 5IntroductionThe S5x family of Eiconcards are ISA cards that offer X.25 connectivity through one or two (depending on the the Eiconcard m

6 Installing the Eiconcard S5xInstalling the Eiconcard S5xFollow the steps below to install the Eiconcard S5x. If you want the Eiconcard S5x to be ava

Installing the Eiconcard S5x 7c)If there is a metal plate at the end of the slot, remove it and keep the screw.d)Firmly insert the adapter into the se

8 Installing the Eiconcard S5x5 Test the Eiconcard S5xThe application software purchased with the Eiconcard S5x contains a test program to verify th

Making an ISDN Connection 9Making an ISDN ConnectionNote Only the Eiconcard S51 supports ISDN connections.After you have installed your Eiconcard S51,