Eicon Networks S93 Guía de instalación Pagina 47
- Pagina / 130
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
AT-command set of the Eicon ISDN Port 47
Completing the Eicon Port driver installation
After accepting the configured parameters, the installation of the Eicon virtual COM Port
driver is complete. Follow the directions on the screen and read the corresponding section
in this manual:
• If you wish to install the Eicon driver for CAPI 2.0, click ‘Ye s ’ to confirm when prompted.
See CAPI 2.0
on page 56.
• If the Security Dynamics Authentication in the ‘Advanced Parameters’ of the
WAN-Miniport driver has been configured, the Eicon Authentication Service must be
installed. Click ‘Ye s ’ when the program prompts for this service to be installed. See also
Eicon Authentication Service
on page 81.
• After the installation process of Diva Server for Windows NT is complete and you have
restarted your computer for the new settings to become effective, you can install the
virtual modems which are to use the Port driver. See Installing virtual modems
on
page 59.
AT-command set of the Eicon ISDN Port
The Eicon ISDN Port driver supports the following AT-command set (parameters enclosed
in square brackets are optional, variables are enclosed in angle brackets). These
commands must be used from within your communications application.
Standard AT commands
Command Description
A/ Repeats the previous command.
AT No operation.
AT A Answer - Has to be issued to accept an incoming call that has been
indicated by a RING.
AT D <Number> Dial - Dials the given number and switches to data mode after successful
connection establishment. (For subaddresses see Subaddress on
page 55.)
AT D <Number>; Dial - Dials the given number but remains in command mode when the
connection has been established. (For subaddresses see Subaddress
on page 55.)
AT DP <Number> Pulse Dialing - Dials according to the pulse code convention (is ignored
with ISDN and treated as ATD). (For subaddresses see Subaddress
on
page 55.)
AT DT <Number> Tone Dialing - Dials according to the multiple frequency convention (is
ignored with ISDN and treated as ATD). (For subaddresses see
Subaddress
on page 55.)
- Diva Server for Windows NT 1
- Reference Guide 1
- Contents 3
- About This Online Guide 5
- General features 7
- Fax and voice features 8
- Supported hardware 9
- ISDN BRI adapters 9
- Diva Server TSP features 9
- Q-Sig features 9
- Channelized T1 (RBS) features 9
- ISDN PRI adapters 10
- T1 adapters 10
- Note on downloaded software 11
- Overview of the software 12
- Driver structure 12
- Installation sequence 14
- Basic drivers 15
- Installing the basic drivers 16
- Configuring the basic drivers 17
- Configuration profiles 18
- Basic Settings 18
- Basic drivers 19 19
- SPID Settings 20
- Advanced Parameters 21
- ISDN Protocol Settings 22
- ISDN Line Settings 23
- Basic drivers 24 24
- WAN-Miniport driver 25
- Port List 26
- WAN-Miniport driver 27 27
- WAN-Miniport driver 28 28
- WAN-Miniport driver 29 29
- Advanced Settings 30
- Shorthold Settings 31
- Authentication Features 32
- Number Checking 33
- WAN-Miniport driver 34 34
- Callback Settings 35
- WAN-Miniport driver 36 36
- Remote Access Service (RAS) 37
- Installing RAS 37
- Configuring RAS ports 37
- Port configuration 38
- Network configuration 39
- Eicon Port driver 41
- Eicon Port driver 43 43
- Phone numbers/extensions 44
- Eicon Port driver 45 45
- Generic Server Modem 46
- Standard AT commands 47
- ISDN-specific AT commands 53
- decoders.) 53
- 600 bps - 48000 bps 55
- CAPI 2.0 56
- CAPI 2.0 57 57
- CAPI 2.0 58 58
- Installing virtual modems 59
- Administration 65
- RAS server setup 69
- Dial-Up Networking monitor 70
- Using Shorthold Mode 72
- … Charged to the RAS client 73
- … Charged to the RAS server 74
- Shorthold and Multilink PPP 74
- Callback numbers 75
- Via modem emulation 76
- The server side 77
- The client side 77
- Via the WAN Miniport 78
- Eicon Authentication Service 81
- Changing Your Installation 82
- Changing the configuration 83
- Uninstalling 84
- CHAPTER 9 86
- Options file 87
- General section 88
- Diva Server adapter section 88
- Protocol 91
- Common components section 101
- Port driver section 104
- CAPI driver section 105
- Script file (OEMSETUP.INF) 106
- Running the installation 107
- Preparing the script file 107
- Restarting the server 110
- Installation example 111
- Installing multiple adapters 112
- Management Tools 113
- Active Connections 114
- System Overview 115
- Properties 116
- Troubleshooting 117
- Troubleshooting 118 118
- Diva Server Diagnostics 119
- Troubleshooting 120 120
- Individual trace options 121
- Predefined trace masks 121
- Minimum trace mask 122
- Troubleshooting 123 123
- Features 124
- Supplementary Services 128
© 2020, manymanuals.es. Todos los derechos reservados | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales