Eicon Networks S93 Guía de instalación Pagina 87
- Pagina / 130
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Installation in Unattended Mode 87
Options file
In unattended mode, the instructions and parameters for the installation are read from a
plain text file known as the options file. The format of the options file is based on the
standard Windows INI format.
[SECTION NAME]
PARAMETER1=VALUE1
For each component a section in the options file is checked. As the Diva Server for
Windows NT software consists of several components (see Driver structure
on page 12),
several sections are required in the options file.
See below for possible components of the Diva Server for Windows NT software. Some
components must be installed, others can be installed depending on the application
requirements:
• Diva Server adapter drivers (must be installed).
• WAN-Miniport driver for RAS support (optional).
• Eicon Port driver for modem-based applications (optional).
• CAPI 2.0 interface for CAPI-based applications (optional).
Note: The CAPI interface must be configured after unattended installation.
The section names (see General rules on section names
below) are predefined and
depend either on the type of Diva Server adapter or on the type of interface. To keep the
installation easy, one options file handles the installation of all components, if only one
adapter is installed. For the installation of multiple adapters see Installing multiple adapters
on page 112.
Numeric values can be given as decimal or hexadecimal values. By default, the system
interprets the values as decimal: Hexadecimal values need the prefix ‘0x’ or the suffix ‘H’.
The following examples show how to edit numeric values.
Parameter1=100
Parameter2=0x64
Parameter3=64H
General rules on section names
There are three types of sections in the unattended installation options file:
• General section (see General section
on page 88).
• Diva Server adapter section (see Diva Server adapter section
on page 88): The names
of the Diva Server adapter sections must be identical to the <InstanceName> in the
batch file used to initiate the unattended installation (see Running the installation
on
page 107). For installing the Diva Server BRI adapter the section name is ‘DSBRI’.
- Diva Server for Windows NT 1
- Reference Guide 1
- Contents 3
- About This Online Guide 5
- General features 7
- Fax and voice features 8
- Supported hardware 9
- ISDN BRI adapters 9
- Diva Server TSP features 9
- Q-Sig features 9
- Channelized T1 (RBS) features 9
- ISDN PRI adapters 10
- T1 adapters 10
- Note on downloaded software 11
- Overview of the software 12
- Driver structure 12
- Installation sequence 14
- Basic drivers 15
- Installing the basic drivers 16
- Configuring the basic drivers 17
- Configuration profiles 18
- Basic Settings 18
- Basic drivers 19 19
- SPID Settings 20
- Advanced Parameters 21
- ISDN Protocol Settings 22
- ISDN Line Settings 23
- Basic drivers 24 24
- WAN-Miniport driver 25
- Port List 26
- WAN-Miniport driver 27 27
- WAN-Miniport driver 28 28
- WAN-Miniport driver 29 29
- Advanced Settings 30
- Shorthold Settings 31
- Authentication Features 32
- Number Checking 33
- WAN-Miniport driver 34 34
- Callback Settings 35
- WAN-Miniport driver 36 36
- Remote Access Service (RAS) 37
- Installing RAS 37
- Configuring RAS ports 37
- Port configuration 38
- Network configuration 39
- Eicon Port driver 41
- Eicon Port driver 43 43
- Phone numbers/extensions 44
- Eicon Port driver 45 45
- Generic Server Modem 46
- Standard AT commands 47
- ISDN-specific AT commands 53
- decoders.) 53
- 600 bps - 48000 bps 55
- CAPI 2.0 56
- CAPI 2.0 57 57
- CAPI 2.0 58 58
- Installing virtual modems 59
- Administration 65
- RAS server setup 69
- Dial-Up Networking monitor 70
- Using Shorthold Mode 72
- … Charged to the RAS client 73
- … Charged to the RAS server 74
- Shorthold and Multilink PPP 74
- Callback numbers 75
- Via modem emulation 76
- The server side 77
- The client side 77
- Via the WAN Miniport 78
- Eicon Authentication Service 81
- Changing Your Installation 82
- Changing the configuration 83
- Uninstalling 84
- CHAPTER 9 86
- Options file 87
- General section 88
- Diva Server adapter section 88
- Protocol 91
- Common components section 101
- Port driver section 104
- CAPI driver section 105
- Script file (OEMSETUP.INF) 106
- Running the installation 107
- Preparing the script file 107
- Restarting the server 110
- Installation example 111
- Installing multiple adapters 112
- Management Tools 113
- Active Connections 114
- System Overview 115
- Properties 116
- Troubleshooting 117
- Troubleshooting 118 118
- Diva Server Diagnostics 119
- Troubleshooting 120 120
- Individual trace options 121
- Predefined trace masks 121
- Minimum trace mask 122
- Troubleshooting 123 123
- Features 124
- Supplementary Services 128
© 2020, manymanuals.es. Todos los derechos reservados | 0.015 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales